[Tanx] Help needed 1989 US model front brake rotor replacement

[Eddy van Keulen via Tanx]

I bought one like this at Harbor Freight more than a decade ago.  I 
place a board on top to make a flat surface and the tube frame rests on 
that just fine. You don't have to remove the "skid plate" either. Just 
wheel the lift underneath and crank 'r up. The only thing to watch for 
is the breather/overflow tubes sticking out the bottom.

Eddy in Morgan Hill, CA

On 7/27/2015 4:33 PM, Don Evans via Tanx wrote:
> Harbor Freight. Get the web coupon for 20% off. Good stuff cheap.
>
>
>
>
> Sent from Samsung tablet
>
>
>
> -------- Original message --------
> From via Tanx <tanx at micapeak.com>
> Date: 07/27/2015 3:25 PM (GMT-05:00)
> To Milt Rudy <miltrudy at gmail.com>,Transalp and NX discussion list 
> <tanx at micapeak.com>
> Subject Re: [Tanx] Help needed 1989 US model front brake rotor 
> replacement
>
>
> http://m.harborfreight.com/1500-lb-capacity-atvmotorcycle-lift-61632.html
>
> Dennis
>
> On Jul 27, 2015, at 2:00 PM, Milt Rudy via Tanx <tanx at micapeak.com 
> <mailto:tanx at micapeak.com>> wrote:
>
>> I used to use a wooden stool with enough boards on top, placed under 
>> the center of the bike, to get one end off the ground.  I got it onto 
>> the stool by leaning it to one side while inserting boards under the 
>> lifted side, then alternating. Later I bought a hydraulic motorcycle 
>> lift from Pep Boys on sale for $50.  They probably cost more now.  
>> But I've used it on many of the bikes I've owned since the Transalps 
>> and it sure makes maintenance easier. Another alternative would be to 
>> use a hydraulic "bottle jack" under the center of the bike to lift 
>> one end and place jack stands to hold it up while you work on the 
>> front end.  Or, if you have a ceiling beam in the garage and a block 
>> and tackle, hoist the front end by the handlebars till it's off the 
>> floor.  Or, I've seen enduro riders lay the bike on its side to 
>> change the tires.  If you have something to cushion the bodywork, 
>> that might be an option.
>> Milt
>>
>> On Mon, Jul 27, 2015 at 11:19 AM, Burr, John H UTAS via Tanx 
>> <tanx at micapeak.com <mailto:tanx at micapeak.com>> wrote:
>>
>>     I need to change the front rotor and Pads (I already have the
>>     parts).  What are thoughts on how to support the Transalp (no
>>     center stand) while I do this?
>>
>>     Thanks,
>>
>>     John
>>
>>
>>     _______________________________________________
>>     Tanx mailing list
>>     Tanx at micapeak.com <mailto:Tanx at micapeak.com>
>>     http://micapeak.com/mailman/listinfo/tanx
>>
>>
>> _______________________________________________
>> Tanx mailing list
>> Tanx at micapeak.com <mailto:Tanx at micapeak.com>
>> http://micapeak.com/mailman/listinfo/tanx
>
>
> _______________________________________________
> Tanx mailing list
> Tanx at micapeak.com
> http://micapeak.com/mailman/listinfo/tanx

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://micapeak.com/pipermail/tanx/attachments/20150727/180a1695/attachment.html>